The lathe is executed by profiles and can install structural elements

The lathe is executed by profiles and can install structural elements Do it yourself siding lathe: technical tips The installation of the siding requires special preparations by the owner. In addition to the basic finishing of the work surface, the installation of the panel also requires the creation of a support frame. This is a slat that can decorate high-quality wall surfaces for a long time.
In some cases, you may not use this design-for example, if you plan to complete a foam block wall. But here, the existence of the crate also proves that it has thermal insulation. Therefore, the conclusion about the convenience of the frame device is obvious-it is necessary.

In order to make self-assembly fully meet the technical requirements, it is worth giving yourself some guidance. According to these guidance, you can build your own closet without the help of experts. In practice, this process does not cause any special difficulties, so as long as the instructions are strictly followed, even people with no architectural experience can cope with this task.
The lathe can be made of wood or metal-therefore, profiled beams Girdler presumption skoogs or steel profiles are used. If you want to rely on durability and high-quality installation, then it is best to choose metal. Its installation is easier, and the finished structure will be more practical. It is more profitable to use wood in houses in the mid-price category. This is an inexpensive solution and can also ensure reliable wall panel installation. But to obtain such results, the material must first be checked for defects, and then it must be treated with corrosion protection. When there are no protruding structural elements on the wall surface, you can start working. These may be drains, platform straps and other details that need to be re-fixed to the surface with siding. It is recommended to carry out the siding lathe on the wall with the smallest height difference. The irregularity of the crate itself will definitely affect the paneling, so all the heights of the supporting frame should be as uniform as possible.
A widely used technique that divides the packaging box into two layers. The first one is used for insulation, the second one directly performs some kind of siding function. The insulation layer is also installed in the wall of the primary lathe, usually made of wood.

-Divide the centimeter piece into two parts and proceed with the 31 cm sheath step accordingly. Strictly increase the step length to the size of the insulation board. On the other hand, this option will retain the best insulation function, but will negatively affect the strength of the slats.

As you can see, a single structure cannot be created without sacrifice. However, if a wooden slatted siding decoration is performed, it is likely to allow 61 cm of steps, and if the cladding involves the installation of metal structures in a brick house, the trimmed insulation panels are more likely to complete its task. The guide itself acts as a holder for the slats. Use self-tapping screws, nails, pins, etc. to install them directly on the wall. These can be suspensions, corners, contours and other elements, and the reliability of the structure will depend on them. First of all, the planks must be fixed, and the planks should have a vertical orientation. This is the case when wood is better than metal used as a sheath element. Essentially, it constitutes the starting position from which the do-it-yourself crate and corresponding support elements will be executed. First, you need to determine the bottom position of the wall panel, and then return 5 cm. At this height, you can attach profiles. This is done along the entire perimeter of the wall, so a level can be observed. In order to maintain the correct fixation in all areas, you should outline the connection points at all corners of the house and pass a rope through them-this will visually mark where the profile is installed.

One of the trickiest stages in the work, because it requires careful calculation and precise processing of the elements used. First, it is necessary to calculate the profile and the location of the installation soffit. The lower boundary can be used as a reference point-the corner profile should be located about 6 below the profile. You can also use self-tapping screws, nails or pins to fix the panel, depending on the material the wall is made of. It can be assumed that the correct lathe for the siding has no butt joints in the profile element. However, if the height of the house exceeds 3, multiple corner profiles must be installed along a line. Before connecting, one of the contours must be cut on the edge. Removed positions with slots for fasteners-their function will be replaced by similar positions on adjacent elements.
Generally, the installation of this component is similar to the installation of an external configuration file. A lower pole was also determined, which was lowered by 6 mm relative to the profile. When installing corner profiles, many people will encounter obstacles in the form of a base, which protrudes directly against the extreme points of the wall panels. In this case, the offset from the contour can be ignored. The most important thing is not to allow the corners to be in close contact with the base, because the smallest movement in the house structure may deform the frame and affect the cladding.

If the metal crate used for the wall panels can provide a certain impact absorption and balance the pressure, then such a gap is very necessary for the wooden elements. In addition, if the height of the house exceeds 3 meters, the elements are spliced ​​together in the same way as the external outline, overlapping by 26 mm.

In the final stage, the framing of the completed structure is carried out in the window and door opening area. The lathe frame with these elements is not connected, but installing the wall panel elements in this area will inevitably interact with the support frame and the frame.
The openings are decorated with the same corners and contours. The main problem lies in the execution of the joint part, which may require trimming the component at an angle. In the future, the same hardware will be used for fixing. Usually, the technology of the lathe device is carried out according to the above description, but at each stage, various deviations and technical contradictions may occur.
If the wall surface is not flat, it cannot be repaired. In this case, you should not refuse to install wall panels and lathes for it. If the question is about how to make a crate in a wooden house, the installation rules will be the same, but there are some special features. For example, vapor and waterproof membranes may be required. Such an intermediate layer is placed in the gap between the main insulating slats and the supporting wall frame.
Strengthening the foundation of the side wall is a necessary technical solution that can provide multiple functions at the same time. It is also impractical to save crates because it will act as a protective layer for the walls of the house, as condensation may form between the main surface and the wall panels. It is best to add a layer of water and thermal insulator on the slats. In this case, the walls of the house and its external appearance will be preserved. It takes less time to master the others. Try it! Sharpening Drill Bits - The Long Way Round