How (and Why) to Wrap a House in Continuous Insulation: Rockwool ComfortBoard.
HOW TO Install a metal frame ceiling
Load more...
.
Installation without wall insulation is cheaper than using insulation materials. Moreover, the process of installing decorative surface materials has also been simplified: installing anti-lattice; installing side panels; installing additional components; installing low tide. Installing vinyl siding without using insulating materials will greatly reduce the heat and sound insulation properties of the facing material. However, in order to save money, this is completely acceptable. This is especially true if the walls of the building are quite wide without providing good thermal insulation properties. Roof drape file The implementation of roof drape file is not only for aesthetic reasons, but also for the functional characteristics of the building facade. A drape file is needed to provide traction in the space under the roof and protect the roof cake from all kinds of (birds, mice, etc.). As it happens, most of the overhangs are covered with wooden lining (1.5-2 cm thick edging board). The edge of the roof usually protrudes more than 601 mm from the wall. The length of the highlight will depend on the application fee. A few years ago, they stopped using the lining, but started using the material-vinyl soffit. Due to the use of soffits to fill, the roof looks very complete. They are installed quickly, do not require special care, do not rot, do not burn, and most importantly provide ventilation for the roof space. The cost of overhanging also includes the installation of profiles and wind deflectors. The windshield is a wooden board that covers the space between the wall and the roof of a building. It prevents blowing out from the attic, so it can ensure that the best temperature is reached there. The installation of basement panels is carried out according to the principle of ventilated facades-similarly, connecting the structure to a metal (wooden) base-a crate. The panel is fixed by a special lock using nails or self-tapping screws. First, install the starting strips (profiles) and install the panels one by one from bottom to top. A panel occupies about 0.5 square meters, so its installation speed is quite high. The cost of completing the basement with external wall panels also includes the installation of corners, rise and fall, and flow elements. You can also order roof windows, door installation, roof installation, drainage system installation and other services related to building improvement separately. Clarified and discussed all of this with the manager of the company engaged in the finishing work. source:- . Pull the moisture barrier to the base in advance, this is especially true for wooden and frame (panel) houses. The placement of the materials is as follows: the canvas is fixed on the surface with 31-41 cm steps, allowing slight sagging. Adjacent strips overlap and are glued with tape. All joints and fasteners are sealed. Pay special attention to the corners: they are covered by solid blocks and there are no seams where the walls meet. Laying the moisture-proof layer The moisture-proof film must be laid on the surface of the facade with the rough side, otherwise the required effect will not work. The wooden frame structure is arranged as follows: the base is laid out in 51-61 cm increments (41-51 cm for basement panels). The pipeline should be perpendicular to the installed wall. Treat steel bars with a section of 51 * 41 or 51 * 51 with protective and refractory compounds. The holes of the fastener are drilled on the surface. The guide rail is exposed according to the mark, and the fixing point is transferred to the wall. Drill holes and finalize the pins (wooden base is optional). Prepare all attachment areas. This bar will be applied to the given position in the level. In order to ensure accurate and reliable alignment, a substrate is used. The self-tapping screw has been screwed in. The schematic diagram of the wooden lathe device needs to obtain a rigid structure with only one plane between the columns. The installation of the metal lathe is carried out using profiles and hangers. The technique is as follows: perform marking. The position of the suspension line is marked on a straight line at a distance of 41-51 cm, holes are punched on it, and the fasteners of the rack are installed. To do this, screw in the pin and screw in the screw. The hanger is bent with letters. The frame is leveled and tightened. Fixing the metal profile to the wall In order to increase rigidity after the house is insulated, jumpers can be installed. note! No matter which method is used to install the frame, the door and window openings must be completed: beams or profiles are fixed along its periphery. Thermal insulation is required before the structure is wrapped with wall panels. There are several ways to do this. Use mineral wool to heat the walls. The mineral wool used for wall panels is very suitable for wooden frames. To improve reliability, two layers can be laid. Work plan for laying mineral wool: the insulation layer is tightly placed at the same height between the racks. Care must be taken not to damage the corners. Place the next row of rails. Place them perpendicular to the previous ones and follow the established steps. The space is again filled with mineral wool. The windbreak layer extends from above. The last beam of the frame was installed, which was necessary for installing the cladding. This position exactly matches the first slat. In this complicated way, not only reliable insulation (exclusion) is achieved, but also ventilation gaps are formed. In order to obtain the best results, it is recommended to fix it with the metal frame. Step-by-step installation instructions: organize the crate, then fix and bend the suspension. According to the size of the insulation board, the condition is marked. The materials are placed in rows and hung on the fasteners of the rack. In order to further fix the board, a special positioning pin with a wide head is used. The position of the rows is offset to avoid overlapping joints. The corners overlap in a checkerboard pattern. Taking into account the expansion of the gap, the gap needs to be treated with polyurethane foam. The windshield is elongated. When all layers are in place, metal posts and jumpers will be installed.
An expansion gap must be left to prevent deformation during thermal expansion. After the fixed guide element has completed the installation of the insulation layer under the wall panel, the main work begins: if necessary, install the drain pipe along the entire length of the wall panel. It will be accurately set in a horizontal position and fixed to the frame. It will drain the liquid evenly and firmly fix the following components. The starting profile is connected to the previously installed drainage system. Without a low tide, the process will be performed in a different way. Measure 5-6 from the ground or blind spot, and mark 41 up from it. If the outer and inner corners have complex contours (the edge of the panel is inserted into them), they will be measured and marked. Along the drawn line, taking into account the offset at the corner, tighten the starting board. Install the starting plate and the corner profile and set the angle slightly lower than the starting profile to obtain a kind of edging. The joint profile should be installed at the end of the panel between the corners. The opening of the window is framed by a platform strap, and a profile rod is installed on the inside. If there is no room for a slope, you can only trim the windows with sidewalls. All elements for fixing window openings must be firmly fixed, and cannot be bent or sagging. If the initial rebar is not enough, place the next rebar a distance of 6-11. When the mounting hole is inconsistent with the fixed position, you need to use a drill or grinder to install it yourself. The installation facade components of the siding are usually placed horizontally: wrap the board around the two corners or around the corners and connecting bars, and then lower it until it clicks. Screw the part to the frame from above through the existing hole with the gap. The following components are installed in a similar manner to the suspended position of the roof. In order to properly handle all problems and eliminate deflection, please check the panel by level. The final stage of finishing work is to install finishing bars under the protruding roof. If necessary, the last panel is trimmed and fed under the tail of the guide rail. More complex options (especially when using metal siding) require the creation of notches along the edges of the panel, through which the elements will fit closely to the final contour. As a finishing touch, it is equipped with a profile rail and a soffit to cover the protruding part of the gable or roof. The use of wall panels and installation of insulating materials is a laborious task, requiring accuracy and compliance with relevant regulations. The result will be a beautiful, noble house. source:, - - - - - - . It is a popular facing material based on polyvinyl chloride. It is mainly used to decorate the exterior walls and walls of various buildings (including private houses). It has many advantages, including the ability to fix the panel while performing work on the insulation of the finished surface. In addition, all necessary activities can be done manually. What is the insulating wallboard made by myself as a cladding wallboard? In the modern market, there are panels of various colors and textures to choose from. Wall panels can successfully imitate wood, brick and stone surfaces. The standard thickness of cladding panels for cladding is 1 mm. The width and length indicators are not limited by standardization and depend on the preference of a particular manufacturer. Generally, cladding panels are about 3-4 in length and 21-26 in width. The large grid allows you to choose the most suitable panel for cladding houses. Siding residential buildings are usually finished with vinyl or any other basement siding. When choosing a specific option with all other conditions being equal, give preference to vinyl panels.
When choosing vinyl siding, be sure to pay attention to the appearance of the elements-the color of the panels should be strictly uniform. Expensive exterior wall panels usually have the same color on both sides. If cheaper materials are used, the inside is usually lighter than the outside. It is not recommended to cover shiny panels. This material will be very hot in the sun until it deforms. Therefore, the best choice is frosted siding. Vinyl siding check that all panels are the same thickness. The parameters of the nail hole must also be the same. Before purchasing materials, check their ductility. To do this, you can fold the thin part of the panel near the nail hole. If the edges are cracked, you should refuse to buy such panels. If the material is bent, but at the same time remains intact, this type of siding can be safely used for insulation coating. Advantages of vinyl siding Advantages of siding There are many different materials on the market today that can be used for insulating cladding. However, the many advantages of siding enable it to firmly establish its position among leaders. Wall panels are vinyl wall panels used for exterior wall decoration of buildings. The main advantages of panels that should be noted include: strong corrosion resistance; affordable panel costs; corrosion resistance. Moreover, the side wall will not contribute to the formation of an environment conducive to the development of various pests; an attractive appearance. The panel is available in a variety of colors and can imitate a variety of materials, so there is no problem in choosing the right finish; durability is easy to install; unpretentious care. For private developers, the undisputed advantage is that they can install vinyl panels with their own hands. This does not require any special skills-enough to know how a hammer works and why a self-tapping screw is needed. At the same time, professional repairmen spend a lot of time on siding finishing. After reading the simple instructions, you can handle all upcoming work yourself, thus saving money. The steps of wall insulation are suitable for installation of wall panels that are simultaneously insulated, and slats made of wood and metal profiles are suitable. In most cases, wooden slats are used. Metal bricks are mainly used according to the requirements of the owners, mainly for brick houses. Use a wooden lathe The first step in using a wooden lathe. Prepare your house to complete the work. If you are not using a new building, but working in a house that has already been constructed and used, please remove various components such as platform straps, blinds, downpipes and all other factors that will affect the installation. The second step. Eliminate any type of defects and damage on the wall. Modern silicone sealants will help you solve this problem. The third step is to install the horizontal slats. Choose the step of placing the rod so that it is 1-1.5 cm smaller than the width of the insulating board. For lathes, it is best to use strips with a cross-section of 45 cm or 55 cm, and fix them with pins or other convenient fasteners. Before installation, soak the wood with a high-quality preservative. the fourth step. Place the insulating board in the crate. Mineral wool and more modern heaters based on it are the best choice for thermal insulation. Place the boards as close as possible, with no gaps at the seams. Place the insulating board in the turning unit. Place the insulating board in the turning unit. Step 5. Lay a layer of waterproof material on the insulating layer. The best choice is a special diffusion membrane. This material will simultaneously protect the insulating material from moisture and provide the necessary ventilation for the space.
Use a construction stapler and staples to glue the film to the strip. The sixth step. Start fixing the vertical slats. Place the column vertically and perform the necessary horizontal inspections. Eliminate irregularities with special pads. To arrange the vertical lathe, it is suitable to use 2.5 cm thick wooden boards. You can fix the siding on the board. Before installing the board, you also need to soak the preservative. The use of metal turning The use of metal turning siding houses are usually used for siding. first step. Get rid of all the elements that may affect the installation. The working principle is the same as the wooden box. The second step. Clean the wall surface thoroughly. Continue cleaning the wall until the sides are no longer loose. The third step is to place your palm on the wall. If traces remain on the skin, make a primer and plaster on the wall. The surface of the wall should be slightly rough. This will provide the highest quality adhesion for insulating materials. the fourth step. Fix the hanger on the wall to install the galvanized profile. the fifth step. Cover the walls with insulating material. In this case, it is more convenient to use foam boards. It can be fixed without fixing. Use specially designed adhesive to fix the circuit board. The sixth step. Fix the elements of the metal slats to the hanger. Side panels will be installed on it in the future. Therefore, you need to select the appropriate turning options, lay the insulation, and then install the cladding. Panel installation It is not difficult to decorate the house with wall panels. This is a simple, consistent job. You just need to follow the instructions to successfully complete each step. The first step of panel assembly. Continue to install the side plate starter strip. To do this, find the lowest point of the house wall, step back 41 mm, and draw a horizontal line on this horizontal line along all the walls of the building. Place the edge of the starter side slat on this marking line, and then fix it on the wall with anchors. A very important point: the nail can not be driven in until the nail stops, but a gap of about 1-2 mm should be left. The panel material will expand and contract with temperature changes. If you keep hammering a nail with a nail, the panel will deform and the cladding will deteriorate. If the length of one starting strip is not enough, please fill in the notch 0.5 cm from the first strip on the second strip. The second step of finishing the facade. Nail special corner decorations at the wall joints. Fix them with nails and hammer them in approximately 21-31 cm increments. Install custom shaped bars around doors and windows. the fourth step. Enter the main stage of siding. To do this, remove the panel, insert its lower edge into the previously fixed starting strip, and nail the upper panel to the crate. The panel cannot extend a few millimeters to the corner of the house in order to be able to expand and contract. Fix the next row in the same way: hook the lower edge of the new row to the protrusion of the previously placed panel, and nail the upper edge to the crate. For exterior wall decoration, wall panels can be fixed with special connecting profiles or simply overlapped. If you like the second option, please fix the panels with an overlap of about 21-31 mm. At the same time, the installation of the cladding must be planned in such a way that the seams are spaced apart-you cannot install them one after the other. You can easily determine the number of nails needed to fix a panel and the steps to place the fasteners during the installation process. The siding has factory holes for nails, guided by them. Drive the nail exactly into the middle of the hole so that the panel can move normally when the temperature is deformed. Drive in the last nail, no more than 81-101 from the edge of the siding. If there is no suitable mounting hole at this distance, please do it yourself. Wall panels are very suitable for walls and exterior walls. Rich textures, sizes and colors will enable you to choose a finish that perfectly fits the landscape. Follow the suggestions received, and you can use your own hands to create a beautiful and durable design for your house. Enjoy your work! source:- - - - - - - - .
The most common mistakes in the insulation of siding houses If you live in the Leningrad region, then you know that our climate is not the warmest. There are few sunny days, and the annual average temperature is 2 to 4.5 degrees Celsius. Therefore, you can spend time comfortably in the villa in only three summer months (even depending on which summer). However, if the house is insulated with wall panels, this period can be extended. In this article, we will figure out together what errors may occur if non-professionals perform insulation under the siding. By the way, you may be interested in an article about errors in the installation of siding: click here (will open in a new window). The most common mistakes made when insulating houses under siding let us immediately figure out: professionals don’t make these mistakes. Every siding professional has his own style, but we all follow some general rules. If you find that the person who insulates your house has made these mistakes, chase them to your neck. It's best to turn to professionals and pay more, but you can guarantee that you won't have to do it again in the future. Let us find out what mistakes we make when insulating a house under the siding. Rolling insulation instead of flat insulation This error is caused by the desire to save material when insulating the house. Rolled insulation is cheaper than flat insulation, and those who do not understand insulation technology tend to save money. Rolling insulating layers cannot be used to insulate vertical surfaces. It is suitable for horizontal surfaces and flat roofs (inclined and flat). If a roll of insulating material is used to insulate the wall, it will quickly fall to the bottom of the wall, and the top of the wall will transfer all the heat from the house to the street. Therefore, when insulating the house under the house, you should always use a plate-like insulating material (we usually use mineral wool). The joints between the insulation panels are loose. If the bonding between the insulation panels is not tight, in fact, gaps will form in the warm walls of your house. Heat-like water, it flows to a place where it can flow more easily. The gap between the insulating plates is such a place. This is why the wooden house is so cold. By the way, we have a good article on placing the log homepage: click here. Your house will be warmer than before the insulation, but some heat will still disappear. I don't think you need it at all. Therefore, please ensure that the person who insulates the walls of your house firmly butts the insulation boards without cracks. When they cover all of this with a windshield, you will not see anything, and your house will not be effectively insulated under the siding. The insulation board is loose. Some local "craftsmen" will confidently tell you that the insulation board is so dense that it cannot be fixed to the wall.
On the pages of the magazine, I collect interesting and curious information from various sources on, process it, check it, and publish it. If you see errors and inaccuracies, please write them in the comments of the group or. In addition, I will always answer any questions. Ask them on the corresponding page at the top of the website. HOW TO Install a metal frame ceiling